Malta Fishing Forum
International Game Fish Association
News:
 
*
Latest Gallery Pictures






WEATHER FORECASTS
Luqa Station Malta North Virtual Buoy West Coast Dingli Cliffs Cirkewwa Mellieha
Pages: [1]
  Print  
Author Topic: Tohatsu M9.9C cooling  (Read 2007 times)
0 Members and 1 Guest are viewing this topic.
SUIGA
Active User
***
Offline Offline

Posts: 10


« on: September 24, 2013, 19:03:00 CET »

Would appriecate any help.....
I have a Tohatsu M9.9c (2 stroke) pre 2002 model which is not passing water through the pee hole,
with a new impeller pump kit replaced.
I tried to open and clogged passage through the hole buy inserting a 6" long flexible pipe with no success.
Any body with suggestions where to remove next?
Logged
The_Gaffer
Senior Moderator Team
Active User
*****
Offline Offline

Posts: 2160


Petecraft 16 Powered by Yamaha 70HP


« Reply #1 on: September 24, 2013, 19:14:03 CET »

Dont know how Tohotsu are set up, but my johnson had the same problem.  The problem lies with the sea water delivery tube to the engine.  It was blocked.  Suggest you to get to the tube, or passage way, you need to take out the lower part of the outboard.  Again, this is the johnson setup, so i suggest you log onto youtube, and che k how tohotsu are set up.
Logged

Beneteau Antares 9.80 - Powered by twin Volvo Penta D4 225HP
     _\____
       /___ \
 ___ /_____\_______
|_______________/
SUIGA
Active User
***
Offline Offline

Posts: 10


« Reply #2 on: September 24, 2013, 19:26:39 CET »

I had a look at the delivery tube when the gearcase was out to replace the impeller kit and was fine, i suspect there might be a blockage somewhere around the combustion chamber passages, but I dont know where to start from.
Logged
Granitu
Active User
***
Offline Offline

Posts: 1502


« Reply #3 on: September 24, 2013, 21:17:09 CET »

You need to open the engine cooling system and work it from there.

Most likely that is were u have the problem. This is a technical matter and i would speak to a mechanic... And goodluck with the outboard once they start suffering from this problem they keep on having the problem...
Logged

Good season so far.....
Destination Sea
VIP Member
Active User
*****
Offline Offline

Posts: 405


« Reply #4 on: October 02, 2013, 23:52:51 CET »

pts to check: -check that the grommet in the cylinder block where the tube fits has not been dislodged upon removal.

ensure that tube is being inserted in head (maybe slight bend)

bleed hole in impellor housing is not closed.

lower unit in a tank:  try turning shaft very fast and see if any water comes out of the tube.

try injecting salt away through the check port (pee phole) before removing head.
Logged

Marino Iside 500 - Etec 90
Buccaneer 130 - Mercury 20
Pages: [1]
  Print  
 
Jump to:  

Recent Posts
[December 09, 2016, 12:28:21 CET]

[November 30, 2016, 15:51:29 CET]

[November 30, 2016, 11:39:21 CET]

[November 28, 2016, 11:08:50 CET]

[November 24, 2016, 07:53:23 CET]

[November 21, 2016, 17:28:42 CET]

[November 21, 2016, 06:19:12 CET]

[November 11, 2016, 16:29:55 CET]

[November 09, 2016, 16:30:38 CET]

[November 03, 2016, 08:27:00 CET]

[November 01, 2016, 14:47:01 CET]

[October 27, 2016, 15:35:07 CET]

[October 26, 2016, 07:03:30 CET]

[October 19, 2016, 18:12:10 CET]

[October 14, 2016, 18:01:32 CET]
Powered by MySQL Powered by PHP Powered by SMF 1.1.21 | SMF © 2015, Simple Machines | TinyPortal v0.9.8 © Bloc

Valid XHTML 1.0! Valid CSS! Dilber MC Theme by HarzeM